Site Loader

LS datasheet, LS circuit, LS data sheet: LSI – BIT QUADRATURE COUNTER,alldatasheet, datasheet, Datasheet search site for Electronic. LSI LS 30 available from 2 distributors. Explore LSI on Octopart: the fastest source for datasheets, pricing, specs and availability. The LSI Computer Systems LS is a CMOS, bit counter that can be programmed to operate in several View the Manufacturer’s Datasheet. Features.

Author: Kegis Zulubei
Country: Liberia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 16 May 2018
Pages: 204
PDF File Size: 15.66 Mb
ePub File Size: 19.37 Mb
ISBN: 972-4-99770-163-6
Downloads: 19345
Price: Free* [*Free Regsitration Required]
Uploader: Gojin

The chip has several other features that can be read about in the datasheet. Note that most pins are active low, and thus must be kept at high at ls166 times unless in use.

Alternatively, at each read the PIC could send back the actual count value. Because of this, the pic software must be written so that the read value of CNTR is modded by the maximum count number to find the position. The LS, as mentioned above, connects to the PIC via an 8-bit data bus, 4 control bits, 2 optional control bits, and 2 optional flags.

(PDF) LS7166 Datasheet download

There are also two pins which output flags when programmed events occur, such as an overflow. Views Page Discussion View source History. The code eatasheet this document only covers divide-by-n binary quadrature mode, and for more advanced features the support code will need to be modified. The value of the PR register is loaded whenever the counter borrows downticks from 0. These pins can be changed, but the data bus read and write functions will need to be changed to interface with bit lines instead of bytes.

  788-312 WAGO PDF

Most other functions will usually not be needed unless special features are needed. Personal tools Log in. In the code below and example schematic, pins B0-B7 are used for the data bus.

LS7166 Datasheet PDF

Retrieved from ” http: Since this was put in the separate function, other code won’t have to be changed, other than TRIS setups. The init function can be modified to utilize other special features of the chip not used here.

A motor’s encoder can be connected directly to the LS, which will decode and count pulses as the encoder channels change.

In any motor-related application, binary counting is necessary. The chip can also operate in divide-by-n mode, which loads the count register with a fixed value on rollover.

Note that to use thethe only daatsheet are to setup the pins, call the init function, then call the read function to get a value.

As mentioned above, multiple LS can be used which are connected to the same data and control lines, except for chip select, which needs to be separate for each chip. The following is a list of registers and the general use of each, even though they are already handled by the code written in a later section.

LS | LSI CORPORATION (LSI LOGIC) | DATASHEET | PHOTO

Because of this, if running the motor backwards continuously counting downthe value of CNTR will always be between 0 and PR at the current position. Eventually the CNTR will overflow if not reduced. This c file simply loops continuously and reads values from the LS This is useful for motor applications, since the fixed value can be set to the number of pulses in a full rotation, and then whenever the count value is read, the exact position of the motor can be known no matter the amount of time that has passed since the last read.

  MAASTRICHTER VERTRAG PDF

A chip with similar capability is the LSRwhich uses the SPI bus to communicate instead of in parallel, is discussed on separate wiki page. This c file contains various functions used to interface with the LS The A and B inputs normally serve as quadrature inputs, like those which come from a quadrature encoder like those on most motors.

LS 데이터시트(PDF) – LSI Computer Systems

The LS communicates with a microcontroller via a bi-directional 8-bit data bus and several control bits. The LS is a 24 bit quadrature counter. For more info on these features, see the datasheet. Using a parallel data bus, a microcontroller can simply read the current count value from the chip, allowing a project to interface with motor encoders without using any additional timers. This number should be changed based on the full rotation count of the encoder in use.

For instance, if the maximum count isand CNTR isthen the actual position is out of All three can be download from this zip file. Note datasheey at the end of the init function, the counter limit value is loaded into the PR register.