Site Loader

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Kazram Karn
Country: Romania
Language: English (Spanish)
Genre: Spiritual
Published (Last): 9 June 2013
Pages: 254
PDF File Size: 3.63 Mb
ePub File Size: 18.65 Mb
ISBN: 327-3-73576-591-9
Downloads: 71099
Price: Free* [*Free Regsitration Required]
Uploader: Zolokazahn

External View And Terminal Blocks 1. For the tuning procedure, refer to the instruction manual of the option card.

If any of the problems listed below occur, take an appropriate measure against them. Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances Page Grounding terminals G Be sure to ground either of the two grounding terminals for safety and noise reduction. Doing so could cause burns. In the following description, the inverter has already been installed.

FUJI ELECTRIC FRENIC-LIFT SERIES INSTRUCTION MANUAL Pdf Download.

Page 60 y codes: Page 85 Table 7. For the inverters with a capacity of 22 kW or below, wait at least 5 minutes; for the inverters with a capacity of 30 kW or above, wait at least 10 minutes. Inverter type Refer to Chapter 1, Section 1. Set up L02 for correct data.

Mounting the covers Put the front cover to the inverter case so that its bottom engages with the hinges provided on both sides of the case. Using the optional multi-function keypad allows you to start and stop the motor, monitor running status, and switch to the menu mode.

  JOSE SANCHIS SINISTERRA AY CARMELA PDF

Install FRENIC-Lift in compliance with the local regulations, Described below for an example, a procedure shows an manula of the inverter in compliance with regulations in Japan. Don’t have an account? Trip with alarm after running for t he period specified by timer y03 2: In the torque control, data of some function codes related frenix the control may be enabled or disabled.

FRENIC-Lift | Fuji Electric Global

frenif Push the front cover against the case of the inverter and slide it upward until the latch at its top engages with the case. In this case, take countermeasures such as installing the inverter in a place that easily protects human body from electric shock. In no event will Fuji Electric Co. Page 34 Table 2.

Fuji Electric FRENIC-Lift series Instruction Manual

You may drop the inverter msnual break it. Tuning procedure What follows gives you a tuning procedure of the inverter for a motor using a multi-function keypad option.

C01 is eff ective during bat tery opera tion. Page 31 These are provided for the DC link bus powered system. To print the manual completely, please, download it.

Table of Contents Preface Icons The following icons are used throughout this manual.

Page 25 Terminal board illustrated in except Figure A. Otherwise, the manuwl may be broken if you turn the power ON. If any of these conditions has occurred, either eliminate the abnormal or error factor s and perform tuning again, or contact your Fuji Electric representative.

Refer to Figure 2. Page 41 Table 2. Page 17 When employing external cooling At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally.

  DISCURSO SOBRE COLONIALISMO AIME CESAIRE PDF

Use them in accordance with your system requirements. Init ialize all function code data to t he factory defaults H04 Auto-resetting 0: Comments to this Manuals Your Name. Take an attention for this structure to connect wires to main output secondary terminals. Check that a mechanical brake is in effect. Read through this instruction manual and be familiar with the handling procedure for correct use.

If any problems persist after the above recovery procedure, contact your Fuji Electric representative. Brake control by time 2: The standard motor lfit the inverter motor are protected in the range of all the frequencies.

Terminal Arrangement And Screw Specifications 2. Chapter 4 Running The Motor U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly. Therefore, if a control signal cable or wire comes into direct contact with a live conductor of the main circuit, the insulation of the sheath or the cover might break down, which would expose the signal wire to a high voltage of the main circuit.

Name of option Function and application Insert an MC in the power source side of the inverter in order to: