Site Loader

(Swedish)Independent thesis Basic level (university diploma), 15 credits / 22,5 HE creditsStudent thesis. Regelsamlingen för byggande innehåller Boverkets byggregler, BBR, med • Regelsamling för konstruktion – Boverkets konstruktionsregler, BKR, . Building permit. On most occasions, you need a building permit if you wish to build a new house, build an addition to your house or if you want.

Author: Samujinn Kedal
Country: Belize
Language: English (Spanish)
Genre: Love
Published (Last): 3 February 2014
Pages: 150
PDF File Size: 15.85 Mb
ePub File Size: 12.93 Mb
ISBN: 886-7-78851-371-5
Downloads: 88413
Price: Free* [*Free Regsitration Required]
Uploader: Tulkis

The fact that the partial safety factor is not part of the Eurocode equations for determining the shear resistance in the same manner as it is in BKR, also contributes to the difference in the values.

The municipal building committee The biverkets building committee shall, among other things, assess whether the design requirements are fulfilled. The form factor is increased in shadow zones. The distance is larger according to Eurocode compared to BKR.

The results of these calculations are presented in Table 3. The snow load reference value depends on the location of the building.

Eurokod1: Laster på bärverk – hur skiljer de sig från Boverkets konstruktionsregler?

konstruktoonsregler If both the length and width of the building are twice as long as the height of the roof ridge, the fixing elements must be selected by taking into account the tensile load in proportion to the following form factor values. This reinforcement should be installed along the entire beam, whether it is needed to achieve sufficient strength or not.

The snow load on the roof is defined by the characteristic value skwhich is calculated as the product of the snow load reference value s0 and the form factor m.

The results in Table 2. Roof without thermal insulation. This thesis aims to show what impact this change from Boverkets structural design rules BKR to the Eurocode will have on the dimensioning of shear reinforcement and the calculation of deformation in concrete beams. Go to the page menu Go to the page content.


Boverkets Konstruktionsregler BKR 94 design standards. The value qk is determined based on the reference wind speed vref, the type of terrain, and the height of the building.

boverkrts The load reduction factor Y is found in the following table. You can also find general information about accessibility, dwelling design, obligatory ventilation control and about the Swedish regulatory hierarchy.

En jämförelse av Eurokod och Boverkets konstruktionsregler

The reason for the introduction of the Eurocode is to try and eliminate trade barriers between member states. Roof with thermal insulation. The municipal building committee shall, among other things, assess whether the design requirements are fulfilled. Then find the value qk bover,ets the tables according to the type of terrain and the building height. Please use this url to cite or link to this publication: Form factor maximum values are specified below in roof schemes according to the roof slope.

Boverket Boverket drafts mandatory provisions and general recommendations in Boverket’s Building Regulations. Taking into account the requirement of minimum reinforcement, table 2.

The boverkehs building committee also has supervisory responsibility for the building works. All measurements are calculated based on the following documents and conditions Sweden: The practical significance of this difference is very small; it only emerges in this thesis when the center distance between the shear reinforcements boverkegs determined in example tree.

It is assumed that the length and width of the building are twice boverekts long as the height to the ridge of the roof.

Compared to table 2. The information presented is suitable for single and double pitched roofs.

Boverkets konstruktionsregler eks-10

When you build a building you need to follow the building code. The value of the wind speed vref is selected based on the location of the building. This is explained by the differences in how the creep rate is determined in the different methods. To examine differences between the calculations of deformation, one method from BKR and one from Eurocode 2 is used.


Eurocode 2 provides a clearer definition of how much deflection can be allowed, it was not supplied in Boverkets structural design rules. Login LT EN e. These two methods are used to calculate how much a beam deforms at different relative humidity. Wind load pull — self-weight. The tables of roof dimensions do not take wind load into account. The regulations you need to know and follow depend on what you want to build or alter.

The relationship between the snow load form factor and roof structure is presented below. The form factor m is used for calculating the dimensions of the cladding. If the wind blows from a certain type of terrain towards a different terrain, the wind load remains the same for the first two kilometers of the new type of terrain.

Swedish Regulations for building works

Wind load on walls. Boverket publishes the Swedish building code. The building code in Sweden contains mandatory provisions and general recommendations. The form factor m depends on wind direction kontruktionsregler the form of the building as presented in the table below and on the next page.

Form factor m is used for selecting the fixing elements of roofing and determining their dimensions.